Ironworking Trainee Guide in Spanish, Level 2

<p style="margin:0px;">(Total Level Hours: 162.5)</p> <p style="margin:0px;">&nbsp;</p> <p style="margin:0px;">30201-11 Trade Math&nbsp;(25 Hours)</p> <p style="margin:0px;">Explains fractions, basic math, and includes multiple opportunities for practical applications.</p> <p style="margin:0px;">&nbsp;</p> <p style="margin:0px;">29106-09 Weld Quality&nbsp;(10 Hours; from Welding&nbsp;Level One)</p> <p style="margin:0px;">Identifies the codes that govern welding, including marine welds. Identifies and explains weld imperfections and</p> <p style="margin:0px;">causes. Describes non-destructive examination practices, visual inspection criteria, welder qualification tests, and the</p> <p style="margin:0px;">importance of quality workmanship.</p> <p style="margin:0px;">&nbsp;</p> <p style="margin:0px;">30202-11 Position Arc Welding&nbsp;(20 Hours)</p> <p style="margin:0px;">Identifies and explains weld joints, weld positions, and open V-butt welds. Describes how to prepare arc welding equipment</p> <p style="margin:0px;">and how to make flat welds, horizontal welds, vertical welds, and overhead welds.</p> <p style="margin:0px;">&nbsp;</p> <p style="margin:0px;">30203-11 Forklifts&nbsp;(17.5 Hours)</p> <p style="margin:0px;">Identifies the basic components of forklifts and the corresponding hand signals. Explains safe practices and how to</p> <p style="margin:0px;">perform inspections. Covers how to read load charts and how to operate forklifts.</p> <p style="margin:0px;">&nbsp;</p> <p style="margin:0px;">30204-11 Trade Drawings Two&nbsp;(10 Hours)</p> <p style="margin:0px;">Introduces types of structural plans and describes the information included on each type. Presents the sequences of</p> <p style="margin:0px;">erection plans for each step of construction and identifies the symbols and abbreviations used on drawings.</p> <p style="margin:0px;">&nbsp;</p> <p style="margin:0px;">38201-11 Intermediate Rigging&nbsp;(10 Hours: from&nbsp;Intermediate Rigger)</p> <p style="margin:0px;">Describes the basic procedures for using the various types of slings and for determining sling stress. Introduces the trainee to</p> <p style="margin:0px;">lift plans, crane load charts, determining the center of gravity of a load, and using cranes to lift personnel. Describes sling</p> <p style="margin:0px;">selection and the use of jacks, hoists, and rollers to move loads.</p> <p style="margin:0px;">&nbsp;</p> <p style="margin:0px;">30205-11 Structural Ironworking Two&nbsp;(30 Hours)</p> <p style="margin:0px;">Describes pre-erection activities for structural steel. Provides procedures for erecting bearing devices, columns, beams,</p> <p style="margin:0px;">girders, joists, bracing, and bridging.</p> <p style="margin:0px;">&nbsp;</p> <p style="margin:0px;">30206-11 Steel Joists and Joist Girders&nbsp;(15 Hours)</p> <p style="margin:0px;">Identifies the types of joists, methods of end support, and the types of bridging available. Explains how to locate the</p> <p style="margin:0px;">ironworking information on framing plans and describes steel joist installation procedures. Describes the conditions necessary</p> <p style="margin:0px;">and the benefits of panelizing bar joist.</p> <p style="margin:0px;">&nbsp;</p> <p style="margin:0px;">30207-11 Tower Cranes&nbsp;(15 Hours)</p> <p style="margin:0px;">Describes safe practices when erecting steel using tower cranes. Explains the difference between erecting steel with a mobile crane versus a tower crane. Describes tower crane hand and verbal signals.</p> <p style="margin:0px;"></p> <p style="margin:0px;"></p> <p style="margin:0px;"></p> <p style="margin:0px;">&nbsp;</p> <p style="margin:0px;"></p> <p style="margin:0px;"></p> <p style="margin:0px;"></p> <p style="margin:0px;">30208-11 Survey Equipment Use and Care&nbsp;One&nbsp;(10 Hours)</p> <p style="margin:0px;">Identifies survey equipment and uses. Explains the proper set up and use of a builder’s level and a theodolite. Covers how to</p> <p style="margin:0px;">shoot elevations, sweep a column for plumb, and set up over a point and back sight to another point.</p>